Lutron LRC Meter LCR-9173 | 60. lcr 9173 100 Hz╱120 Hz╱1 KHz╱10 KHz

Description FEATURES * 6000 counts ADC resolution. Capacitance ( Cp/Cs ) : D 0.1, 0.5V(rms≦ ) * Dual power supply , Battery or AC/DC Adapter. * High performance analog front end for impedance Range Accuracy Accuracy (Z) measurement. 100 Hz 120 Hz * Support Z / DCR measurement for LCR mode. 600 pF ± ( 3.5% 5d ) ± ( 3.5% 5d ) * Four different test frequency are available : 6000 pF ± ( 2.5% 5d ) ± ( 2.5% 5d ) 100 Hz/120 Hz/1 KHz/10 KHz for L/C/R measurement. 60 nF ± ( 2.0% 5d ) ± ( 2.0% 5d ) * Built-in simple DMM front end circuit to support 600 nF ± ( 2.0% 5d ) ± ( 2.0% 5d ) DCV / Freq. / Diode mode. 6000 nF ± ( 1.5% 5d ) ± ( 1.5% 5d ) * Test AC signal level : 0.5 V rms typically. 60 uF ± ( 1.5% 5d ) ± ( 1.5% 5d ) * Test range : ( ex. F = 1 KHz ) 600 uF ± ( 1.5% 5d ) ± ( 1.5% 5d ) L : 600.0 uH to 60.00 H 6000 uF ± ( 2.5% 5d ) ± ( 2.5% 5d ) C : 600.0 pF to 600.0 uF 10 mF ± ( 3.5% 5d ) ± ( 3.5% 5d ) R : 60.00Ω to 20.00 MΩ * Low battery voltage detector. Range Accuracy Accuracy * Min. source resistance : 120Ω typical. 1k Hz 10 kHz * 6 ratio resistor range used for LCR mode. 600 pF ± ( 2.5% 5d ) ± ( 2.0% 5d ) * Support buzzer sound driver with driving pattern 6000 pF ± ( 2.0% 5d ) ± ( 1.5% 5d ) & frequency selectable. 60 nF ± ( 2.0% 5d ) ± ( 1.5% 5d ) 600 nF ± ( 1.5% 5d ) ± ( 1.5% 5d ) GENERAL SPECIFICATIONS 6000 nF ± ( 1.5% 5d ) ± ( 1.5% 5d ) Display LCD size：46.5 X 45.5 mm. 60 uF ± ( 1.5% 5d ) ± ( 2.5% 5d ) Test frequency 100 Hz/120 Hz/1 KHz/10 KHz 600 uF ± ( 2.5% 5d ) ——————- MODE L/C/R L/C/R Function selector 6000 uF ——————- ——————- Frequency selector 10 mF ——————- ——————- D/Q/θ selector Remark : SER/PAL selector * Don’t apply voltage larger than 30 V to input terminals. DCV DCV/Freq./Diode selector * Discharge capacitor before measurement. Dissipation factor 0.0000 to 1999 * If intend to obtain the accurate value, please test Quality factor 0.0000 to 1999 the component. θ measurement ± 90° into the ” Pin terminals ” ( 3-7, Fig. 1 ) or tested Calibration Open/Short calibration via optional. Data Hold Freeze the display reading SMD tester, SMDA-22 or SMD test clip, SMDC-21. Power off Auto shut off saves battery life or manual off by push button Inductance ( Lp/Ls ) : D ≦ 0.1, 0.5V(rms) Operating 0℃ to 50℃ temperature Range Accuracy Accuracy Remark Operating Less then 85% R.H. 100 Hz 120 Hz humidity 600 uH ——————- ——————- Power Supply 006P DC 9V battery 6000 uH ——————- ——————- * Alkaline or Heavy duty type 60 mH ± ( 2.0% 5d ) ± ( 2.0% 5d ) DC 9V adapter input 600 mH ± ( 1.5% 5d ) ± ( 1.5% 5d ) * AC/DC power adapter is optional. 6000 mH ± ( 1.5% 5d ) ± ( 1.5% 5d ) Power DC 6 mA approximately 60 H ± ( 1.5% 5d ) ± ( 1.5% 5d ) After consumption calibration Dimension 151 x 78 x 43mm 200 H ± ( 2.5% 5d ) ± ( 2.5% 5d ) After Weight 235 g * meter only calibration Standard * Instruction manual……….1 PC Accessories * Alligator clips………………1 PC Range Accuracy Accuracy Remark Included 1k Hz 10 kHz Optional SMD tester, SMDA-22 600 uH ± ( 2.5% 5d ) ± ( 2.5% 5d ) After Accessories SMD test clip, SMDC-21 calibration AC to DC 9V adapter 6000 uH ± ( 2.0% 5d ) ± ( 2.0% 5d ) 60 mH ± ( 1.5% 5d ) ± ( 1.5% 5d ) ELECTRICAL SPECIFICATIONS (23±5 ℃) 600 mH ± ( 1.5% 5d ) ± ( 1.5% 5d ) 6000 mH ± ( 1.5% 5d ) ± ( 1.5% 5d ) Resistance ( DCR ) 60 H ± ( 2.5% 5d ) ——————- After calibration Range Accuracy Remark 200 H ——————- ——————- 60 Ω ± ( 1.5% 5d ) After calibration Remark : 600 Ω ± ( 1.0% 5d ) * Discharge inductor before measurement. 6000Ω ± ( 1.0% 5d ) * If intend to obtain the accurate value, please test the 60 KΩ ± ( 1.0% 5d ) component 600 KΩ ± ( 1.0% 5d ) into the ” Pin terminals ” ( 3-7, Fig. 1 ) or tested 6000 kΩ ± ( 1.0% 5d ) via optional 20 MΩ ± ( 1.5% 5d ) After calibration SMD tester, SMDA-22 or SMD test clip, SMDC-21. Resistance(Z) ( Rp/Rs ) 0.5V(rms) Scale range configuration Range Accuracy Accuracy Remark 100 Hz/120 Hz 1k Hz LCR mode 60 Ω ± ( 1.5% 5d ) ± ( 1.5% 5d ) After calibration Function Frequency Meas. Range Min. 600 Ω ± ( 1.2% 5d ) ± ( 1.2% 5d ) mode resolution 6000Ω ± ( 1.2% 5d ) ± ( 1.2% 5d ) Inductance 100/120Hz 60.00mH~200.0H 0.01mH 60 KΩ ± ( 1.2% 5d ) ± ( 1.2% 5d ) Ls / Lp 1kHz 6000uH~60.00H 1uH 600 KΩ ± ( 1.2% 5d ) ± ( 1.2% 5d ) 10kHz 600.0uH~6000uH 0.1uH 6000 kΩ ± ( 1.2% 5d ) ± ( 1.2% 5d ) 100/120Hz 60.00nF~10.00mF 0.01nF 20 MΩ ± ( 2.0% 5d ) ± ( 2.0% 5d ) After calibration Cs / Cp 1kHz 6000pF~600.0uF 1pF 10kHz 600.0pF~60.00uF 0.1pF Range Accuracy Remark 100/120Hz 60.00Ω ~20.00MΩ 0.01Ω 10 kHz Rs / Rp 1kHz 60.00Ω ~20.00MΩ 0.01Ω 60 Ω ± ( 1.5% 5d ) After calibration 10kHz 60.00Ω ~20.00MΩ 0.01Ω 600 Ω ± ( 1.2% 5d ) DC resistance N/A 60.00Ω ~20.00MΩ 0.01Ω 6000Ω ± ( 1.2% 5d ) 60 KΩ ± ( 1.2% 5d ) DMM mode 600 KΩ ± ( 1.2% 5d ) Function mode Meas. Range Min. resolution 6000 kΩ ± ( 1.2% 5d ) DCV 600.0mV~20.00V 0.1mV 20 MΩ ± ( 3.0% 5d ) After calibration Remark : * Don’t apply voltage larger than 30 V to Frequency 6.000kHz~15.00MHz 1Hz input terminals.